최신 CATE 000-109 무료샘플문제:

1. A client is designing a system to support three 24x7 applications, each in a different environment. The plan is to host these applications on a new POWER7 based server to add to their existing POWER6 servers. Virtual I/O Server will not be used.
The applications have the following OS and processor requirements: AIX 6.1 with a peak of 2 cores between 10am-2pm
AIX 5.3 with a peak of 2 cores between 5pm-10pm
AIX 5.2 with a peak of 2 cores between 3am-7am
Outside the peak periods, the processor utilization is extremely low.
Which of the following configurations supports the design requirements?

A) A minimum of four processor activations is required.
Two dedicated processors for an AIX 5.2 LPAR.
AIX 5.3 and AIX 6.1 can share 2 processors
B) Each applications each needs its own LPAR running native AIX.
The LPAR must be running the appropriate version of AIX.
The LPARs can all use the shared pool and be uncapped.
C) The LPAR profiles can set the processor mode to POWER6
The AIX 6.1 and AIX 5.3 LPARs can be migrated using Live Partition Mobility.
The AIX 5.2 could only be migrated if it is in a WPAR.
D) The AIX 5.2 can be hosted in a WPAR in an AIX 7.1 LPAR.
The AIX 5.3 and AIX 6.1 can each have their own LPAR.
All LPARs can use the shared processor pool.

2. An administrator plans to implement Active Memory Expansion on several LPARs on a Power 770 system. Which tool should be used to determine the recommended LPAR settings for Active Memory Expansion?

A) amestat
B) amemon
C) amelpar
D) amepat

3. After installing a new VIO server partition an administrator noticed that the time zone is incorrectly set to CST6DST. The administrator would like the time zone set to Europe/London. Which command will achieve this?

A) chsys -timezone Europe/London
B) chzone -zone Europe/London
C) chtime -tz Europe/London
D) chdate -timezone Europe/London

4. An administrator must create several production and development LPARs on a new Power 770 server. Processor requirements for the development LPARs change frequently.
Which configuration will isolate the production LPARs from changes in processing requirements for the development LPARs?

A) Assign the development partitions to Shared Processor Pool 1 with the Maximum Pool
Capacity equal to the Entitled Pool Capacity.
Assign the production partitions to the default Shared Processor Pool 0.
B) Assign the production partitions to Shared Processor Pool 1 with the Maximum Pool
Capacity higher than the Entitled Pool Capacity.
Assign the development partitions to Shared Processor Pool 2 with the Maximum Pool
Capacity higher than the Entitled Pool Capacity.
C) Assign the production partitions to a Shared Processor Pool 2 with the Maximum Pool
Capacity equal to the Entitled Pool Capacity.
Assign the development partitions to the default Shared Processor Pool 1.
D) Assign the production partitions to Shared Processor Pool 1 with the Maximum Pool
Capacity equal to the Entitled Pool Capacity.
Assign the development partitions to Shared Processor Pool 2 with the Maximum Pool
Capacity equal to the Entitled Pool Capacity.

5. A redundant pair of VIO Servers is used to virtualize the same SAN LUNs to a number of AIX LPARs. To ensure that Multipath 10 is correctly configured an administrator sets the appropriate device attributes on the vSCSI disks on the clients.
One of the VIO Servers was shut down for 5 minutes to simulate a failure. After the VIO Server was brought back online, the administrator found that some LPARs recovered their storage paths automatically, yet some LPARs did not recover their paths at all.
How can the administrator recover from the lack of path recovery?

A) Update SDDPCM to a level higher than 2.1.2.3.
B) Allocate both vSCSI adapters to the client LPARs.
C) Reboot the client LPARs.
D) Reduce the number of paths to the LUNS to 6 or less.

질문과 대답: